Kan-Vick Industries - Deals in Cables. Epoxy, Rubber Products, Valves, Hose Pipes, Flenges, Nut Botl Fasters, and other industrial Porducts Kan-Vick Industries - Deals in Cables. Epoxy, Rubber Products, Valves, Hose Pipes, Flenges, Nut Botl Fasters, and other industrial Porducts
Kan-Vick Industries - Deals in Cables. Epoxy, Rubber Products, Valves, Hose Pipes, Flenges, Nut Botl Fasters, and other industrial Porducts
Home
Products
About Us
Contact Us
Kan-Vick Industries - Deals in Cables. Epoxy, Rubber Products, Valves, Hose Pipes, Flenges, Nut Botl Fasters, and other industrial Porducts

 

 

 

 

 

     

Aluminium Products

Aluminium Sheets / Coils

INDUSTRIAL PRODUCTS

  • Aluminium Sheets & Coils are used as a raw material for making Caps.

 

 

 

 

  • Pharma Blister Foils for tablets, capsules packaging laminates in Pharmaceutical sector.

 

 

 

 

CONSUMER PRODUCTS

KANVICK has now also entered in to Consumer Products business in aluminium foil. We are marketing Aluminium Foil containers like Casseroles, Oven Cups & House foils.

Aluminium House foil is also used for barbecuing more delicate foods such as mushrooms and vegetables; food is wrapped in foil then placed on the grill, preventing loss of moisture that may result in a less appealing texture.

 

Aluminium Casseroles

Semi rigid container for food storage, casseroles, baking cups in food sector.

 

 

Aluminium General Engineering Products

We offer premium quality General Engineering Components for our global clients. These components are used for general industrial and engineering purposes.

Aluminium Flat Bars & Tubes

We are offering vide range of extruded Flat Bar & tubes as per customer requirement as well as standard sizes as per industry specific requirements. These Flat Bars & Tubes are commonly used in transmission and distribution industry & in control panels.

STEEL FLAT PRODUCTS

Flat products include plates, hot-rolled strip and sheets, and cold-rolled strip and sheets; all have a great variety of surface conditions. They are rolled from slabs, which are considered a semi finished product and are normally not sold. Provided by either a continuous caster or rolled from ingots by a slabbing mill, slabs are 50 to 250 millimeters thick, 0.6 to 2.6 metres wide, and up to 12 metres long (that is, 2 to 10 inches thick, 24 to 104 inches wide, and up to 40 feet long).

Plates are hot-rolled either from slabs or directly from ingots. Maximum dimensions vary with available slab sizes or ingot weights and with the sizes of installed rolling mills and auxiliary equipment. Thickness can be as low as 5 millimeters, but it is usually heavier (e.g., 25 millimeters) and can go as high as 200 millimeters. The width of plates is usually between 1.5 to 3.5 metres, but there are plants that can roll plates up to 5.5 metres wide. The maximum plate length that the largest mills can produce is 35 metres. Plates are usually made in small quantities and to a customer’s specification, with different dimensions and tolerances for flatness, profile, straightness, and other properties. The edges can be ordered in either as-rolled condition or sheared, machined, or gas-cut. Plates are also sometimes cladded with corrosion-resistant sheets.

Hot-rolled strip is often shipped directly from the hot-strip mill in a large coil weighing 10 to 35 tons. Its thickness is 1.5 to 12 millimeters, and its width, depending on the available mill, is 0.7 to 2 metres. Frequently, the large coils are slit into narrower coils or edge trimmed, or they are cut to length into sheets at the finishing section of a steel plant or at a service centre. Coils and sheets are shipped either with the hot-rolled surface or with the scale removed and the surface oiled.

Cold-rolled strip, produced from hot-rolled strip, is 0.1 to 2 millimeters thick and also up to 2 metres wide, depending on a shop’s facilities. Steel plants supply this product in coils or sheets, the latter being cut on special shear lines. Cold-rolled products are available in a great variety of surface conditions, often with a specific roughness, electrolytically cleaned, chemically treated, oiled, or coated with metals such as zinc, tin, chromium, and aluminum or with organic substances. They are usually produced to strict dimensional tolerances in order to assure efficient performance in the highly demanding operations of automated consumer-products industries.

Jump To Another Product
[Rubber & Moulded Products - Rubber, PVC & PTFE]
[Hydraulic Hoses & Rubber Pipes]
[SS Flexible hose assemblies]
[Bright Steel Bars]
[Valves & Strainers]
[Pipe / Pipe Fittings & Flanges]
[Nut Bolts & Fasteners]
[Filtration Systems ]
[Epoxy Systems & Their Applications]
[Cables]
[Rubber Mats For Electrical Purposes]

[Electrical & Instrumentation accessories]

Copyright 2001 Kan-Vick Industries. All Rights Reserved